De-install

Do you have to paint, renovate or do any other work at home? Then, we have instructions that will help you to de-install one or some of your alarm components.

Domonial Keypad (GKP model)
Domonial Keypad (GKP model)

De-install

Read Instructions Read Instructions
Domonial PIR Motion Sensor with Camera
Domonial PIR Motion Sensor with Camera

De-install

Read Instructions Read Instructions
Domonial smoke detector (DFS8M model)
Domonial smoke detector (DFS8M model)

De-Install

Read Instructions Read Instructions
Domonial Magnet Contact Sensor
Domonial Magnet Contact Sensor

De-Install

Read Instructions Read Instructions
Domonial Panel
Domonial Panel

De-Install

Read Instructions Read Instructions

Please carefully review these instructions before proceeding to avoid damaging components. There may be a cost to replace any components that are damaged during renovations. If you need help, contact us via chat.

De-install
  1. Unscrew the screw at the top of the keypad with a small Phillips (crosshead) screwdriver 
  2. Slide the keypad up from the bracket 
  3. Once the keypad has been removed, unscrew the 3 screws that are securing the bracket to the wall with a Phillips (crosshead) screwdriver 
  4. Once de-installed, place bracket back onto the back of Keypad and insert screw at the top of the Keypad to secure bracket. Keep in a safe location to avoid it being misplaced or damaged. 
De-install
  1. Insert flat-headed screwdriver into the slot underneath the middle of the sensor. Push screwdriver away from you to release the cover. 
  2. Take the sensor off the mounted wall bracket. 
  3. Unscrew the 4 screws that are securing the bracket to the wall with a Phillips (crosshead) screwdriver. 
  4. Once de-installed, place bracket back onto the back of the sensor and keep in a safe location to avoid it being misplaced or damaged. 
De-install
  1. Twist smoke detector clockwise to remove the component from bracket on ceiling. 
  2. With a Phillips (crosshead) screwdriver, remove the screws that are securing the bracket to the ceiling. 
  3. Once de-installed, place the smoke detector back on to the bracket and twist to secure. (By doing this, it will avoid any tamper activations after it has been taken down). Keep the sensor in a safe location to avoid it being misplaced or damaged. 
De-install
  1. With a Phillips (crosshead) screwdriver, remove the small screw on the side of the larger sensor. 
  2. Insert flat headed screwdriver into the T shaped slot on the larger sensor. Turn the screwdriver to release the cover. 
  3. Once the cover has been removed, unscrew the 2 screws that are securing the bracket to the door/window with a Phillips (crosshead) screwdriver. 
  4. To remove the small sensor (magnet piece) insert a small flat headed screwdriver into the slot at the end of the sensor to release the cover.  
  5. Unscrew the 2 screws that are securing the bracket to the door/window with a Phillips (crosshead) screwdriver. 
  6. Once de-installed, place bracket onto the back of each sensor and keep in a safe location to avoid it being misplaced or damaged. 
De-install
  1. Unplug panel from mains socket. 
  2. Locate the Phillips screw on the side of the panel and remove using a Phillips (crosshead) screwdriver. 
  3. Using a flat headed screwdriver insert it into the top of the slot where the Phillips screw was located and pull the screwdriver handle towards you. This will release the catch, and the panel lid can be easily removed. 
  4. Once the panel lid has been removed, unscrew the 4 screws in each corner with a Phillips (crosshead) screwdriver to remove the panel from the wall. 
  5. Place panel lid back on to panel and keep in a safe location to avoid it being misplaced or damaged.